- AIR QUALITY - HEATING COOLING - LAUNDRY - LIGHTING - MONITORS ALARMS - SEALING - Tools for the Energy Auditor - VENTILATION - WATER -

	Handi Foam
	Two-part foams mix in the nozzle connecting paired cans of foam components. The result is a spray of foam that has an R-value of 6.5 per inch. Cured foam can be trimmed, sanded and painted. It is typically used for insulating hot tubs, around pipes and ductwork, and other small residential insulating projects. Foam does not contain formaldehyde. Cures in less than one minute. Each kit includes 12 extra nozzles 26.5 lbs., Yields 8.75 Cubic Feet PE II-105 - - - - $266.50* 41 lbs., Yields 17.08 Cubic Feet PE II-205 - - - - $396.00* 115 1bs. Yields 50 Cubic Feet PE II-605- - - -$738.64* Please note: A $40.00 haz mat shipping fee applies to these products because they are under pressure. *These products can only be shipped to a business address.
	Options
	Quantity desired

Click on picture to view full-size image	Tu Tuff Vapor Barrier
	Tu-Tuff provides a barrier against air and moisture penetration. Wrap it completely around the house including ceilings, and around walls right up to the windows and doors. Foundations are wrapped around the outside perimeter from the base to ground level and the Tu-Tuff is laid under the concrete flooring making the problems of moisture penetration and dampness absolutely minimal. Because Tu Tuff is cross laminated it has 3.6 times the tensile strength and 6.4 times the puncture resistance of the standard 4 mil low density poly. It is also pinhole free, an impossibility with typical barriers. Because Tu Tuff stops moisture and wind chill, the structure is warmer, drier and easier to heat with less energy. PE TT - - - - - - 14¢ / sq. ft., white 100' x 4', 9',10', 12', and 20' rolls.
	Roll Size
	Quantity desired

Click on picture to view full-size image	Reflectix
	Reflectix is an insulation, radiant barrier, and vapor barrier combined into one product. It is 5/16" thick, made of layers of foil bonded to a tough layer of polyethylene, with two inner layers of bubblepack to resist heat flow. When installed with an air space, it provides a heat barrier equal to much thicker widths of traditional insulating material. The R-value when the direction of the heat flow is up is 8.3; down: 14.3; horizontal: 9.8. It can be used wherever you would use any other insulation product. It has the added advantages of being moisture resistant (perfect for basements and crawl spaces), it is easier to install (just use a stapler and a scissors), and it presents no health hazards for the installer or the building occupant. PE REF - - - - - - .365 $ / sq. ft. 2' or 4' x 25', 50', 100' or 125'
	Roll Size
	Quantity desired

Click on picture to view full-size image	Reflectix Concrete Slab Insulation
	Reflectix Concrete Slab Insulation consists of seven layers. The first layer of white poly is bonded to foil to protect from lime in curing concrete. Each outer layer is bonded to a tough layer of polyethylene for strength. Two inner layers of insulating bubbles resist conductive heat flow while a center layer of polyethylene gives the product high reliability and strength. It is installed with the white side up. The combined R-value of all layers is 1.1. This product is especially useful in radiant floor systems and snow melt systems, as the product will spread heat evenly across the concrete slab. It also acts as a vapor and radon retarder. It is non-toxic and unaffected by moisture or humidity. temperature range -60º to +180º nominal thickness 5/16 inch weight 1.25 oz/sq.ft. puncture resistance 60 lb/inch mold and mildew resistant compression 6% PE CSI----- .375/sq.ft.
	sizes
	Quantity desired

	Plastic Reusable Interior Storm Window Kits
	Our Tyzall plastic kits are applied over the interior window so that they block drafts entering through cracks around the sash as well as heat loss through the glass. The airtight seal also prevents moisture from reaching the cold window glass to form frost. These window kits contain a roll of 4 mil clear plastic, and an adhesive-backed frame strip. They take about ten minutes to install. A scissor is the only tool that you will need. Cut the strips to size, stick them to your window frame, and snap in the clear plastic for a tight seal against cold air, frost, and drafts. Plastic snaps out and rolls up for summer storage. UV inhibitors resist yellowing and cracking for 5 years or more. Much more economical than the one-season models that use a blow dryer to install. PE 4050 - - 40" x 50," 20 kits / case - - $96.00 / case PE 5080 - - 50" x 80," 20 kits / case - - $125.00 / case PE 7282 - - 72" x 82," 15 kits / case - - $131.00 / case
	Sizes
	Quantity desired

Click on picture to view full-size image	Battic Door Attic Access Insulator
	Are you heating and cooling your attic? If you do not have any attic hatch insulation, you are. Your access door is usually made of a thin layer of plywood with no insulation, and no tight seal. Conditioned air from your home easily enters the attic through this uninsulated hole in your attic floor. The Battic Door Kit includes a triple-wall white coated cardboard base with four walls to serve as an enclosure for a pull-down staircase, foam tape weatherstripping, foil insulation and instructions. Flaps are secured to the outside of the open bottomed R-5 box. R-7 foil insulation is applied to the exterior of the box, then weatherstripping is applied to the existing frame of the stairway. The open bottom box sits on this weatherstripping and the stairs fold into the box. The price also includes an insulation kit. The kit consists of a larger open bottomed box with reflectix material on all five sides. Put the included R-50 fiberglass over the Battic Door, and put this unit into the reflective covered box for a highly insulated attic hatch. No Tools are required for putting together and installing the Battic stair cover and insulation kit! 22 1/2" x 54" X 13" deep with insulation kit PE BDSIN - - - $119.00 25 1/2" x 54" x 13" deep with insulation kit PE BDSLIN - - - $119.00 .
	sizes
	Quantity desired

Click on picture to view full-size image	Insulated Attic Hatch and Ladder
	This insulated (R-10) and weatherstripped attic hatch provides easy access without leaving a huge hole in your insulation. Because it comes as a completely trimmed unit, it is very easy to install. The plywood outer shell of the door is painted white, so no refinishing is necessary. The hinged fold-up ladder can easily be cut down for ceilings up to 104". For higher ceilings, ask about our extensions. Self trimming flange design conceals the drywall edge, eliminating the need for molding. Closes with a gas-piston counterbalance similar to those used in hatchback cars , in place of unreliable and dangerous springs. Specifications \| PE AL Frame and ladder, pine with doweled rungs. Insulated top panel, 2" rigid polystyrene. Rough opening: 44.25" x 22.75" Note: this item has a freight upcharge of $52.00 included in the price PE AL - - - - $585.60 For higher than the 104" ceiling, use the PE EX extension to access ceilings up to 125". PE EX- - - - $64.00 The same insulated and weatherstripped attic access door but without the ladder. For use in knee walls or ceilings where a permanently mounted ladder is not required. Insulated Ceiling Attic Hatch \| PE AH Same rough openings as above. Ceiling attic hatch only. Note: this item has an additional freight charge of $20.00 included in price PE AH - - - - $272.00
	Options
	Quantity desired

	Energy Guard Insulated Attic Hatches
	Energy Guardian makes an insulated kit to fit over any type of attic access opening. Each is a two piece system with a lip and a lid. While the kits can easily be put together by a handy home owner, there are trained installers throughout the country. If you would like the name of the experienced installer closest to you, please let us know in the comment section of the order form. The attic ladder cover PE ESSAS is a two piece system. The 7 1/2" lip allows for your ladder to fit in in its folded position above the attic floor. An R-39 insulated lid fits snuggly on top of the lip creating a thermal and infiltration barrier. The lid weighs 10 lbs, and the frame 5 lbs. It will fit any opening that is less than 35" x 63". PE ESSA----$230.50 If you have a push up hatch with no stairs, you will need the PE HC R-39 insulated push up hatch cover. It will fit any attic opening (measured inside the attic) less than 28 1/2" x 32". This unit requires 7" of clearance above the attic floor - the total height of the lip and lid.. PE HC---- $134.00 This product also comes with joist framing units for hatches that are not framed in in the attic. PE HCJ---- $140.00 If the access to your attic is up a standard walk up flight of stairs, the PE WUS also is an R-39 with a 10 lb cover, and fits any footprint less than 94 1/2" x 44" PE WUS----$295.00 Last, the knee wall insulation kit has a 9 lb lid, and is insulated to an R-24. It will fit any opening 36" x 36" or smaller. PE KW----$125.00
	Models
	Quantity desired

Back to Positive Energy Conservation Products Home Page